Guide · Homeowners · 4 min read · Updated 17 November 2026
Kitchen Island Extractor Options: Ceiling, Downdraft or Hood
Short answer
There are three main island extraction options: a suspended island hood, a ceiling-recessed extractor, or a downdraft unit built into the worktop. Fitting and ducting typically costs £400–£1,100, excluding the appliance. Ducted extraction to an outside wall is more effective than recirculating, and the best choice depends on your ceiling height, duct route and how open you want the space.
Why island extraction is harder
A wall hood benefits from the wall behind it, which helps guide steam and grease upwards. An island hob is open on all sides, so cross-draughts from doors and windows can pull cooking fumes away before the extractor captures them. Island extractors therefore need to be sized and positioned carefully, and the duct has to travel through the ceiling void or under the floor to reach outside.
Before choosing a model, the installer will check which way your ceiling joists run, how far it is to an outside wall and whether there is a room above. Ducting along the joists is straightforward. Running across them may mean a boxed-in bulkhead or a lowered ceiling section.
The three main types
Each option suits a different room. The table compares the practical points.
A suspended hood remains the most reliable performer because its canopy sits close to the rising steam. It needs a strong fixing, usually a timber or steel frame between joists, and the chimney section is cut to suit your ceiling height. Ceiling-recessed extractors are popular in modern open-plan rooms, but sit further from the hob, so they need a larger fan to achieve similar capture. Downdraft extractors either rise from the worktop behind the hob or are built into the hob itself, and suit rooms where any overhead unit would block a view or where the ceiling cannot be opened.
| Type | Best for | Watch out for |
|---|---|---|
| Suspended island hood | Strong capture, rooms with standard ceiling height | Blocks sightlines, needs secure fixing into joists |
| Ceiling-recessed extractor | Clean look, higher ceilings | Needs a deep enough void and extra power to compensate for height |
| Downdraft extractor | Open views, rooms with a room or flat roof above | Takes cupboard space, less effective with tall pans |
Ducting, ventilation and the rules
Rigid round or flat-channel ducting performs better than flexible hose, and every bend and metre of length reduces airflow. Installers aim for the shortest, straightest run with as few bends as possible and an external wall vent with a non-return flap. Where the duct passes through an unheated loft, it should be insulated to reduce condensation running back to the extractor.
Approved Document F of the Building Regulations sets minimum extract rates for kitchens. If you are replacing an existing extractor or moving cooking to an island, the new arrangement should still meet those minimums. Where an extractor is installed in the same room as an open-flued gas or solid fuel appliance, the installer must make sure it will not draw fumes down the flue, which a Gas Safe engineer can check.
- Keep the duct diameter at least as large as the extractor outlet
- Limit bends and avoid long flexible runs
- Fit an external vent with a back-draught flap
- Insulate ducts passing through cold spaces
- Allow access to grease filters and motors for cleaning
Recirculating extraction
Where ducting outside is impossible, for example in some flats or where the ceiling cannot be opened, a recirculating extractor uses grease filters and carbon filters to clean the air and return it to the room. It removes some grease and odour but does not remove moisture, and carbon filters need regular replacement. It is a fallback rather than a first choice, and you will still need adequate background ventilation in the kitchen.
Noise, power and sizing
Extractor performance is quoted as an airflow figure in cubic metres per hour. A common rule of thumb in the trade is to aim for enough airflow to change the air in the kitchen around ten times an hour, though open-plan rooms and island positions often need more because there is no wall to help guide the fumes. Bigger is not always better: an oversized motor running flat out is loud, and most people turn noisy extractors down or off, which defeats the point.
Noise is quoted in decibels, usually at the highest and lowest settings. If quiet operation matters, look at the figure for the normal setting rather than the boost setting, and consider a remote or inline motor fitted further along the duct in the ceiling void or roof space. That moves the motor noise away from the kitchen. The installer should also confirm the hood is at least as wide as the hob, and ideally a little wider for an island position.
- Check the airflow figure against the size of the open-plan space
- Compare noise at the everyday setting, not just boost
- Consider an inline or remote motor for quieter running
- Choose a hood at least as wide as the hob
Planning the installation
Extraction is best planned at the same time as the island. The duct route for a ceiling hood is usually run during the first fix, before the ceiling is patched and decorated, while a downdraft unit needs its duct planned through the island plinth and under the floor. A suspended hood also needs its power supply and a secure fixing point between or onto joists. When we arrange an island with a hob, the joiner, electrician and extraction fitter work to one plan so the hood, the hob and any pendant lights line up properly.
Questions people also ask
Are downdraft extractors as good as hoods?
Downdraft extractors capture steam close to the hob and work well for most everyday cooking, especially with low pans. They are generally less effective than a well-sized hood with tall stockpots, because rising steam escapes above the intake. They also take up cupboard space in the island beneath the hob.
How high should an island hood be above the hob?
Manufacturers usually specify a distance, often around 650 to 750 mm above an induction hob, and sometimes more above gas. Always follow the appliance instructions. Too high and the hood loses capture, too low and tall people bump into it while cooking.
Can I fit island extraction in a flat?
Often, yes, but the duct route needs checking. If you cannot reach an outside wall without crossing a neighbour's space or a fire compartment, a recirculating unit may be the only option. Leaseholders should also check the lease, because external vents can need the freeholder's consent.
Written and checked by the Kitchen Island Builders team. Read our editorial policy.
More guides
How Much Does a Kitchen Island Cost in the UK?
A small kitchen island built from standard units with a laminate top costs £1,200–£2,500 fitted. A medium island with a quartz or oak top and seating…
What Size Kitchen Island Do I Need? Space and Clearance Guide
Leave roughly 1 metre of clear walkway around a kitchen island, and up to 1.2 metres where two people cook or where an appliance door opens into the…
Sink or Hob in a Kitchen Island: Which Is Better?
A sink in the island suits sociable kitchens where you prep facing the room, and costs £450–£1,200 to plumb. A hob in the island needs extraction…
Bespoke vs Standard-Unit Kitchen Islands: Which to Choose
A standard-unit island uses ready-made 600 mm carcasses from a kitchen range and costs from around £1,200–£2,500 for a small fitted island. A bespoke…
Get a free kitchen island builders quote
Tell us what you need and we'll come back with a clear price.
Request a quote